# /etc/rc.d/rc.inet1.conf # # This file contains the configuration settings for network interfaces. # If USE_DHCP[interface] is set to "yes", this overrides any other settings. # If you don't have an interface, leave the settings null (""). # You can configure network interfaces other than eth0,eth1... by setting # IFNAME[interface] to the interface's name. If IFNAME[interface] is unset # or empty, it is assumed you're configuring eth. # Several other parameters are available, the end of this file contains a # comprehensive set of examples. # ============================================================================= # Config information for br0: # Note the added "BRNICS" variable which contains a space-separated list # of the physical network interfaces you want to add to the bridge. IFNAME[0]="br0" BRNICS[0]="eth0" IPADDR[0]="192.168.0.1" NETMASK[0]="255.255.255.0" USE_DHCP[0]="" DHCP_HOSTNAME[0]="" # Config information for eth1: IPADDR[1]="" NETMASK[1]="" USE_DHCP[1]="" DHCP_HOSTNAME[1]="" # Config information for eth2: IPADDR[2]="" NETMASK[2]="" USE_DHCP[2]="" DHCP_HOSTNAME[2]="" # Config information for eth3: IPADDR[3]="" NETMASK[3]="" USE_DHCP[3]="" DHCP_HOSTNAME[3]="" # Default gateway IP address: GATEWAY="192.168.0.10" # Change this to "yes" for debugging output to stdout. Unfortunately, # /sbin/hotplug seems to disable stdout so you'll only see debugging output # when rc.inet1 is called directly. DEBUG_ETH_UP="no" ## Example config information for wlan0. Uncomment the lines you need and fill ## in your info. (You may not need all of these for your wireless network) #IFNAME[4]="wlan0" #IPADDR[4]="" #NETMASK[4]="" #USE_DHCP[4]="yes" #DHCP_HOSTNAME[4]="icculus-wireless" #DHCP_KEEPRESOLV[4]="yes" #DHCP_KEEPNTP[4]="yes" #DHCP_KEEPGW[4]="yes" #DHCP_IPADDR[4]="" #WLAN_ESSID[4]=BARRIER05 #WLAN_MODE[4]=Managed ##WLAN_RATE[4]="54M auto" ##WLAN_CHANNEL[4]="auto" ##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7" ##WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16" #WLAN_WPA[4]="wpa_supplicant" #WLAN_WPADRIVER[4]="ndiswrapper" ## Some examples of additional network parameters that you can use. ## Config information for wlan0: #IFNAME[4]="wlan0" # Use a different interface name nstead of # the default 'eth4' #HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address #MTU[4]="" # The default MTU is 1500, but you might need # 1360 when you use NAT'ed IPSec traffic. #DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten #DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten #DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change # your default gateway #DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP # server #WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameter # defined in rc.wireless.conf, by prepending # 'WLAN_' to the parameter's name. Useful for # those with multiple wireless interfaces. #WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey" # Some drivers require a private ioctl to be # set through the iwpriv command. If more than # one is required, you can place them in the # IWPRIV parameter (separated with the pipe (|) # character, see the example).